Program loader (Firmware) and configuration (SETUP) for all DMD products, industrial or for LRS / XLRS systems long range (FPV/UAV). To update a device, connect the BOOTADMD-V3 through the RCBUS connection of the device and the PC by USB port. Load firmware and setup configuration of the devices DMD are performed with software software DMDStudio on the button (BOOT) or also with old software (BOOTLOADER). We recommend using the latest version of software DMDStudio. RCBus Connection (GND, Positive(3V3),Data), if you are connected in reverse it will not work, but the device is not damaged. There are other devices with mini usb direct connection and don't require BOOTADMD-V3. To upgrade or configure, only is necessary DMDStudio software.   MAIN FEATURES:

• Switch to power RCBUS to 3.3V.
• Button. To wake up dispositives ultra low power consumption as PMAN, RadioBeacon, etc.

  SPECIFICATION:

1 Led (ON/OFF). 1 Switch to power RCBus to 3.3V. 1 Button. 1 Micro USB (Micro-B).

  COMPATIBILITY:

With most DMD products: LRS Systems, XLRS Sytems, industrial products.

  CONTENT:

x1 BOOTADMD-V3.

  *Micro USB cable not included. Delivery date: Can be shipped within 1-2 days.

This is a new Pixhawk flight controller set including orange cube and the ADS-B carrier board. This open source autopilot adopting more powerful H7 processor, featuring triple redundancy IMU system and vibration dampening system.The anti-jamming performance and stability are greatly improved. Carrier Board with an integrated 1090MHz ADS-B receiver, allowing the software to receive information about the location of manned aircraft in the area, that effectively improve the flight safety of UAV. Here 3 GPS is a new version based on the Here 2 GNSS GPS unit. Compared with the Here GNSS GPS unit, the Here 3 GPS module features more accurate positioning, faster response, and colored LED lights for visible indication of UAV status. Compatible with XLRS and XVID systems.  

New Features:

• Cube Orange:

  • Includes new generation of more powerful H7 processor, with stronger performance, faster processing, increased security with built-in triple redundant sensors, temperature control shock absorption IMU.

  • Separate IMU and MFU, reduces sensor interference.

• • Uavionix ADS-B Receiver.

  • With the help of flight software, Cube Orange can completely fly any remotely controlled aircraft, helicopter or multirotor and turn it into a more professional UAV platform.

• ADS-B Carrier Board:

  • A standard carrier board with an integrated 1090MHz ADS-B receiver allowing the software to receive information about the location of manned aircraft in the area.

  • Receives information such as position, altitude, speed, etc. which can all be viewed in Mission Planner.

  • Through settings, you can optionally set up your cube to allow the drone to automatically avoid aircraft that are within an exclusion zone.

• GPS Here 3:

  • Accuracy: 3D: 2.5 meters / RTK 0.025 meters.

  • Processor: STM32F302.

  • IMU sensor: ICM20948.

  • Concurrent reception of up to 3 GNSS (GPS, GLONASS, BeiDou).

  • Advanced inhibitor detection and signal spoofing.

  • CAN port.

  • Status RGB LEDs.

  • Accelerometer/ Gyro/ Barometer / Compass.

  • 8Hz refresh rateBuilt-in IMU H.

 

• General Pixhawk 2.1 Cube Key Features:

  • Built-in IMU Heating system, allowing flights at extreme temperature(-10°C~+55°C)

  • Robust DF17 Interface connectors give enhanced drop and shock resistance.

  • Aircraft: VTOL, Multicopter, Helicopter, Plane, General Robotics

  CONTENT: (Cables for accessories are JST to DF13 cables which are compatible with old pixhawk accessories, such as Telemetry, Power Brick or GPS):

x1 PIXHAWK2.1 Cube Orange.

x1 PIXHAWK2.1 Standard Set ( ADS-B Receiver).

x1 GPS Here 3.

x1 POWER Brick Mini.

x1 SD Card(inserted in Cube).

x2 TELEM Cable.

x1 POWER Cable.

x1 I2C Cable.

x1 BUZZER Cable.

x1 MICRO USB Cable.

x1 GPS1 Cable(with saftey switch).

x1 GPS2 Cable.

x1 I2C Splitter.

x4 Mounting Screws(M2.5*8).

x1 3M Double Sided Foam Tapes.

  Note: Telemetry cables are modified to connect Plug & Play with compatible XLRS devices and Pixhawk Cube autopilot is tested and preconfigured to work with XLRS systems.   Delivery date: Can be shipped within 3-5 days.

Cable USB Dongle to mini jack 3.5mm (PPM pulses or PWM serie) support 12 Channels adapted for XLRS transmitters. Connect the adapter to the SPPM output of your XLRS transmitter and your PC to get up to 12 channels. (Valid for XLRS transmitters: D2, D3, D4 of the 2020 version).   BASIC USES

- Output for simulator on PC. For example for Aerosim.

- Use XLRS Transmitter as standard Joystick on a PC. (For Mission planner, QGround Control or similar).

  For more information, click here: 

- SPPM output on XLRS transmitters.

  * The images shown on this page are for reference only and may differ from the final products. Delivery date: Can be shipped within 2-3 days.

LED Lights Controller Electronic Switch 2A, 2 channels for RC FPV, Drone, Car, Boat, Robots...   CONTENT:

• 1x SWLED. Electronic switch two channels, LED lights controller.

  Delivery date: Can be shipped within 2-3 days.