Return to previous page
Grid
List
Show
Placeholder

ADV-PROD-LOG-25-2025-1. 85% down payment for production for the first batch of 25 units of the SATPR...

CTRCB. Serial TTL to RCBUS Converter.

CURCB is used to adapt an RCBus interface to Serial TTL (38400b). In this way you can connect a tracker antenna like SATPRO to a dataLink from other brands, to use the Mavlink protocol in streaming. Normally it is necessary together with CURCB and SATPRO when we use a Datalink from other brands that are not XLRS.   Functioning:

2 modes:

Boot.

Streaming & Commands.

  Conections:

It has two connectors, a more robust one for power and RCBus that connects to the SATPRO PC and a stereo RCBus Jack with TTL serial that connects to the Data Link. For its complete operation it is necessary to use the CURCB module to connect the PC via USB.

It is powered by RCBus Connector from SATPRO.

Warning: Connections must be made only with the SATPRO turned off. If not, it is possible that the SATPRO or the fuse may break.

  RCBUS:

SATPRO native communications. Use a special cable with power.

Speed: 1Mb. Synchronous binary packages.

IP8:     9

  Serial TTL:

Level: TTL 0v to +3.3V.

Speed: 38400b by default or 115200b if necessary.

Bandwidth: 40kb. You cannot send a streaming with more than 4kbytes/sec even if the port speed is 115200b.

Serial TTL TXRX connector connection (Data Link):

Black:  GND          Base Jack Red:    RX    (Out) Jack Tip White: TX    (Inp)  Half Jack

  LEDs:

On, turns on when you activate the SATPRO.

TX and RX. They light up when there is data to or from the DataLink.

  Manual:   Content:

x1 CTRCB. Serial TTL to RCBUS Converter.

x1 Cable Jack Connector to SP13 connector for SATPRO-RCBUS.

x1 Cable with MiniJack conector to RC Connector (3pins).

CURCB. USB to RCBUS converter for SATPRO.

CURCB is used to adapt an RCBus interface to USB. In this way you can connect a tracker antenna like SATPRO to a PC, to give it commands or use the Mavlink protocol in streaming. Normally it is necessary together with CTRCB and SATPRO when we use a Datalink from other brands that aren't XLRS.   Functioning:

3 modes:

Boot.

Commands.

Streaming.

  Conections:

It has two connectors, one for USB type “C” that connects to the PC and another RCBus that connects to the SATPRO. Only with the CURCB module you can command the SATPRO, but to use the Mavlink download protocol, the CTRCB module that complements it will be necessary.

  RCBUS:

SATPRO native communications. Use a special 7m cable.

Speed: 1Mb. Synchronous binary packages.

IP8:     10

  USB:

It is powered by USB.

Speed: 115200b fixed.

  LEDs:

Power, turns on when you connect the USB.

TX and RX. They light up when there is data to or from the USB.

  Manual:   Content:

x1 CURCB. USB interface Module for SATPRO.

GCS-PDHDMI. Passive hdmi duplicator 1 in 2 out for GCS, to connect and view video at the same time w...

You can connect GCS Monitor and another HDMI device (Video Glasses, external monitor or similar) to view the video at the same time on two different HDMI devices.   Note: This product only works with GCS XLRS.   Estimated delivery time: 15-20 days. *The images and information is preliminary, it is possible that the final product has changes.

KITD5DUALSTRR_001. Full XLRS System (15Km), Redundant Radio Control & Mavlink Telemetry 250Km, ...

Complete XLRS kit that contains several XLRS devices to have a redundant system on the same frequency, it can be 863-950Mhz or 433Mhz, that is, it has two TX modules and two RX modules working in redundancy. With this set you can get Radio Control & Telemetry 863-950Mhz or 433Mhz up to 250Km (LOS) and 2.4Ghz Digital Video up to 15Km (LOS). On the ground: You have a Dual Ground Control Station D5 along with the tracker antenna that will have the two redundant TX modules and the RX digital video module, along with a auxiliary small XPAD1W controller that will be connected via Wifi (It can be used in case of takeoff and landing for example). In the Drone, UGV, USV...: You have two redundant RX modules along with the digital video transmitter.   Get more information about the products:

Ground Control Station Dual D5

SATPRO. Professional Smart Antenna Tracker.

XVHD_SAT. Digital Video System

XPAD1W. Small Remote Controller

  Content:

x1 GCSD5DUAL. Dual Ground Control Station D5.

x1 WMX481R-V2. Redundant transmitter radio module for connection and communication with XLRS Remote Controllers (863-950Mhz, 1W, -116dBm).

x1 RXLRSR-V2. (Redundant Mode) Professional RX, Radio Control, Mavlink Telemetry / Transparent Data Link, FHSS, AES128 Encryption, 8CH, SPPM, SBUS, RCB, SMA-F, USB, (863-950Mhz, 1W, -116dBm).

x1 XVHD-15. Full HD Digital Video system (XVTR & XVRE) for 150Km (LOS), x1 HDMI, x1 Ethernet, ODFM, H264/H265, AES128 Encryption, (2.4Ghz, 4-8W).

x1 SATPRO_28480. Professional Smart Antenna Tracker with SJJ32 Tripod.

x1 XPAD1W. Small Remote Controller, Radio Control, Wifi, USB. (Without XLRS Radio).

  Delivery date: Can be shipped within 60-90 days.

KITD5DUALSTRR_002. Full XLRS System (250Km), Redundant Radio Control & Mavlink Telemetry 250Km,...

Complete XLRS kit that contains several XLRS devices to have a redundant system on the same frequency, it can be 863-950Mhz or 433Mhz, that is, it has two TX modules and two RX modules working in redundancy. With this set you can get Radio Control & Telemetry 863-950Mhz or 433Mhz up to 250Km (LOS) and 2.4Ghz Digital Video up to 150Km (LOS). On the ground: You have a Dual Ground Control Station D5 along with the tracker antenna that will have the two redundant TX modules and the RX digital video module, along with a auxiliary small XPAD1W controller that will be connected via Wifi (It can be used in case of takeoff and landing for example). In the Drone, UGV, USV...: You have two redundant RX modules along with the digital video transmitter.   Get more information about the products:

Ground Control Station Dual D5

SATPRO. Professional Smart Antenna Tracker.

XVHD_SAT. Digital Video System

XPAD1W. Small Remote Controller

  Content:

x1 GCSD5DUAL. Dual Ground Control Station D5.

x1 WMX481R-V2. Redundant transmitter radio module for connection and communication with XLRS Remote Controllers (863-950Mhz, 1W, -116dBm).

x1 RXLRSR-V2. (Redundant Mode) Professional RX, Radio Control, Mavlink Telemetry / Transparent Data Link, FHSS, AES128 Encryption, 8CH, SPPM, SBUS, RCB, SMA-F, USB, (863-950Mhz, 1W, -116dBm).

x1 XVHD-150. Full HD Digital Video system (XVTR & XVRE) for 150Km (LOS), x1 HDMI, x1 Ethernet, ODFM, H264/H265, AES128 Encryption, (2.4Ghz, 4-8W).

x1 SATPRO_28480. Professional Smart Antenna Tracker with SJJ32 Tripod.

x1 XPAD1W. Small Remote Controller, Radio Control, Wifi, USB. (Without XLRS Radio).

  Delivery date: Can be shipped within 60-90 days.

KITD5RR. Full XLRS System, Redundant Radio Control & Mavlink Telemetry, Digital Video Full HD w...

KITD5STRR_001. Full XLRS System (15Km), Redundant Radio Control & Mavlink Telemetry 250Km, Digi...

Complete XLRS kit that contains several XLRS devices to have a redundant system on the same frequency, it can be 863-950Mhz or 433Mhz, that is, it has two TX modules and two RX modules working in redundancy. With this set you can get Radio Control & Telemetry 863-950Mhz or 433Mhz up to 250Km (LOS) and 2.4Ghz Digital Video up to 15Km (LOS). On the ground: You have a Ground Control Station D5 along with the tracker antenna that will have the two redundant TX modules and the RX digital video module, along with a auxiliary small XPAD1W controller that will be connected via Wifi (It can be used in case of takeoff and landing for example). In the Drone, UGV, USV...: You have two redundant RX modules along with the digital video transmitter.   Get more information about the products:

Ground Control Station D5

SATPRO. Professional Smart Antenna Tracker.

XVHD_SAT. Digital Video System

XPAD1W. Small Remote Controller

  Content:

x1 GCSD5. Ground Control Station D5.

x1 WMX481R-V2. Redundant transmitter radio module for connection and communication with XLRS Remote Controllers (863-950Mhz, 1W, -116dBm).

x1 RXLRSR-V2. (Redundant Mode) Professional RX, Radio Control, Mavlink Telemetry / Transparent Data Link, FHSS, AES128 Encryption, 8CH, SPPM, SBUS, RCB, SMA-F, USB, (863-950Mhz, 1W, -116dBm).

x1 XVHD-15. Full HD Digital Video system (XVTR & XVRE) for 150Km (LOS), x1 HDMI, x1 Ethernet, ODFM, H264/H265, AES128 Encryption, (2.4Ghz, 4-8W).

x1 SATPRO_28480. Professional Smart Antenna Tracker with SJJ32 Tripod.

x1 XPAD1W. Small Remote Controller, Radio Control, Wifi, USB. (Without XLRS Radio).

  Delivery date: Can be shipped within 45-60 days.

KITD5STRR_002. Full XLRS System (250Km), Redundant Radio Control & Mavlink Telemetry 250Km, Dig...

Complete XLRS kit that contains several XLRS devices to have a redundant system on the same frequency, it can be 863-950Mhz or 433Mhz, that is, it has two TX modules and two RX modules working in redundancy. With this set you can get Radio Control & Telemetry 863-950Mhz or 433Mhz up to 250Km (LOS) and 2.4Ghz Digital Video up to 150Km (LOS). On the ground: You have a Ground Control Station D5 along with the tracker antenna that will have the two redundant TX modules and the RX digital video module, along with a auxiliary small XPAD1W controller that will be connected via Wifi (It can be used in case of takeoff and landing for example). In the Drone, UGV, USV...: You have two redundant RX modules along with the digital video transmitter.   Get more information about the products:

Ground Control Station D5

SATPRO. Professional Smart Antenna Tracker.

XVHD_SAT. Digital Video System

XPAD1W. Small Remote Controller

  Content:

x1 GCSD5. Ground Control Station D5.

x1 WMX481R-V2. Redundant transmitter radio module for connection and communication with XLRS Remote Controllers (863-950Mhz, 1W, -116dBm).

x1 RXLRSR-V2. (Redundant Mode) Professional RX, Radio Control, Mavlink Telemetry / Transparent Data Link, FHSS, AES128 Encryption, 8CH, SPPM, SBUS, RCB, SMA-F, USB, (863-950Mhz, 1W, -116dBm).

x1 XVHD-150. Full HD Digital Video system (XVTR & XVRE) for 150Km (LOS), x1 HDMI, x1 Ethernet, ODFM, H264/H265, AES128 Encryption, (2.4Ghz, 4-8W).

x1 SATPRO_28480. Professional Smart Antenna Tracker with SJJ32 Tripod.

x1 XPAD1W. Small Remote Controller, Radio Control, Wifi, USB. (Without XLRS Radio).

  Delivery date: Can be shipped within 45-60 days.

KITD5STRR_100. Full XLRS System (250Km), Redundant Radio Control & Mavlink Telemetry 250Km, Dig...

Complete XLRS kit that contains several XLRS devices to have a redundant system on the same frequency, it can be 863-950Mhz or 433Mhz, that is, it has two TX modules and two RX modules working in redundancy. With this set you can get Radio Control & Telemetry 863-950Mhz or 433Mhz up to 250Km (LOS) and 2.4Ghz Digital Video up to 100Km (LOS). On the ground: You have a Ground Control Station D5 along with the tracker antenna that will have the two redundant TX modules and the RX digital video module. In the Drone, UGV, USV...: You have two redundant RX modules along with the digital video transmitter.   Get more information about the products:

Ground Control Station D5

SATPRO. Professional Smart Antenna Tracker.

XVHD_SAT. Digital Video System

  Content:

x1 GCSD5. Ground Control Station D5.

x1 WMX481R-V2. Redundant transmitter radio module for connection and communication with XLRS Remote Controllers (863-950Mhz, 1W, -116dBm).

x1 RXLRSR-V2. (Redundant Mode) Professional RX, Radio Control, Mavlink Telemetry / Transparent Data Link, FHSS, AES128 Encryption, 8CH, SPPM, SBUS, RCB, SMA-F, USB, (863-950Mhz, 1W, -116dBm).

x1 XVHD-100. Full HD Digital Video system (XVTR & XVRE) for 100Km (LOS), x1 HDMI, x1 Ethernet, ODFM, H264/H265, AES128 Encryption, (2.4Ghz, 4-8W).

x1 SATPRO_28480. Professional Smart Antenna Tracker with SJJ32 Tripod.

  Delivery date: Can be shipped within 45-60 days.

SATPRO_REP. Professional Smart Antenna Tracker with WMX481 transmitter module and XVRE video receive...

Professional automatic tracking antenna for Radio Control, Mavlink Telemetry and Video systems, for all types of applications with Aerial, Land or Maritime Vehicles. SATPRO is a tracking system, composed of a rotating head, two arms where the antennas are placed and an anchoring system to a fixed base or tripod. The main function is to automatically follow the position of the vehicle, orienting the antennas to obtain the best possible RF link at all times in LOS (Line Of Sight) applications. This set is prepared to function as a repeater, allowing you to easily expand the range of any application. When the main system loses signal or has a very low signal, the repeater activates and the tracker antenna continues tracking the vehicle, thus optimizing performance in LOS applications and non-line-of-sight (NLOS) scenarios. Includes:

x1 SATPRO: Professional antenna tracker.

x1 WMX481: Transmitter module for Radio Control and Telemetry.

x1 XVRE: Full HD video receiver.

Get more information about the product:

SATPRO. Professional Smart Antenna Tracker.

XVHD_SAT. Digital Video System

Delivery date: Can be shipped within 45-60 days (Depending on the options selected).
Quick View Select options This product has multiple variants. The options may be chosen on the product page

XVHD-FX. Radio Control, Data link and Full HD Video System 2.4Ghz.

Radio Control, Data link and Full HD Video System 2.4Ghz. The XVTR aerial unit has HDMI/Ethernet/AV and other video interfaces, 2 UART interfaces and 1 SBUS output interface. The ground unit XVRE has HDMI/Ethernet (RJ54), 2 UART interfaces and 1 SBUS input interface. The serial port supports Mavlink protocol and transparent protocol. Both units have AES128 encryption. For Radio Control: You can use a standard transmitter and connect it through the SBUS of the XVRE ground unit. Then on the XVTR Aerea unit you can connect the SBUS to an autopilot (Cube, Pixhawk, APM...) or similar device. For mavlink telemetry or transparent data link: You can connect the UART of the XVTR air unit to the telemetry port of the autopilot (Cube, Pixhawk, APM) or other device. Then on the XVRE ground unit you can connect it through the UART (Using a TTL - USB serial converter to connect it to the PC) or through Ethernet (UPD or TPC) (You can also watch the video at the same time) and connect to any software like Mission Planner, QGroundControl or similar. For Video: On the XVTR air unit you can connect to the camera or gimbal via HDMI or Ethernet. Then on the XVRE Ground unit you can connect a screen via HDMI or through the Router or PC to Ethernet. If it is required to obtain more range in Radio Control and Telemetry, then a second integrated system can be used at 433Mhz or 863-950Mhz with a range of 250Km (LOS) that will work together with a GCS XLRS, this will work at the same time with the system 2.4Ghz, consult about the XVHD-SAT product. Note: To obtain these ranges it is necessary to use a SATPRO tracker antenna or similar.   Delivery date: Can be shipped within 30-45 days (Depending on the options selected). *The images and information is preliminary, it is possible that the final product has changes.

Digital Micro Devices S.L Copyright © 2024

Home
Shop
0 Cart